Can I Install a Tub Myself? Considerations And Also Steps
Can I Install a Tub Myself? Considerations And Also Steps
Blog Article
Were you trying to locate related information about How to Install a Bathtub?
Setting up a bath tub isn't exactly brain surgery, but it does require solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily easily accessible, the task can relocate quickly; if you have to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the work and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you begin. Chances are you may need an expert plumber to make tube links.
This write-up will help you install a new tub in your shower room if you have actually currently bought a new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your devices and also product list need to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the limited accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location in between the faucet and the sink. Safeguard the tap in position with the producer provided backnut. As soon as the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, position the bathtub in the needed setting. The wood boards are handy in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the tub till the level reads level.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly settle it into its final setting.
Planning for the Installment
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about issues with dampness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack rather early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very eager about A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed my entry. In case you enjoyed reading our blog entry if you please make sure you remember to share it. Thanks a lot for going through it.
Request An Estimate
Report this page